This is a fairly simple fix, you will use a method called 3-10's: step 1 is to turn key on engine off. step 2 is turn key to start briefly then let off (maybe a second and then just let off key) step 3 remain inside vehicle do not touch anything for approx. 10 mins. then on your message board the security will quit blinking . step 4 at this time you will turn the key off for FIVE mins. and turn back on. repeat step 1-4 TWO more times, after this time you can turn the key off once again and your done the next time you cycle the key, the fob should be programmed to your computer. good luck
im sorry i recently posted a fix for key to computer here is how u fix the key fob's, again sorry for the false info..
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder - do not turn ignition switch.
Press and hold the DOOR unlock switch (This is the switch on the door, NOT the remote).
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF ON, OFF. (2 TIMES)
Release the DOOR unlock switch. The doors will lock and unlock one time to confirm the program mode is actuated. Remove the key from the ignition.
Simultaneously press and hold the LOCK button and the UNLOCK button on one key less remote for approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters. Reprogram any existing remotes at this time as they have been erased.
Turn the ignition switch to the ON (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
im sorry i recently posted a fix for key to computer here is how u fix the key fob's, again sorry for the false info..
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder - do not turn ignition switch.
Press and hold the DOOR unlock switch (This is the switch on the door, NOT the remote).
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF ON, OFF. (2 TIMES)
Release the DOOR unlock switch. The doors will lock and unlock one time to confirm the program mode is actuated. Remove the key from the ignition.
Simultaneously press and hold the LOCK button and the UNLOCK button on one key less remote for approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters. Reprogram any existing remotes at this time as they have been erased.
Turn the ignition switch to the ON (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.
Answers & Comments
This is a fairly simple fix, you will use a method called 3-10's:
step 1 is to turn key on engine off.
step 2 is turn key to start briefly then let off (maybe a second and then just let off key)
step 3 remain inside vehicle do not touch anything for approx. 10 mins. then on your message board the security will quit blinking .
step 4 at this time you will turn the key off for FIVE mins. and turn back on.
repeat step 1-4 TWO more times, after this time you can turn the key off once again and your done the next time you cycle the key, the fob should be programmed to your computer. good luck
im sorry i recently posted a fix for key to computer
here is how u fix the key fob's, again sorry for the false info..
Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder - do not turn ignition switch.
Press and hold the DOOR unlock switch (This is the switch on the door, NOT the remote).
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF ON, OFF. (2 TIMES)
Release the DOOR unlock switch. The doors will lock and unlock one time to confirm the program mode is actuated. Remove the key from the ignition.
Simultaneously press and hold the LOCK button and the UNLOCK button on one key less remote for approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters. Reprogram any existing remotes at this time as they have been erased.
Turn the ignition switch to the ON (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation.