Turn the bulb assembly counterclockwise 1/6 turn, pressing in firmly, until the flanges align with the slots in the retainer ring.
Pull out the bulb assembly. You may have to rock it up and down slightly to loosen it.
Disconnect the bulb base from the harness by lifting the plastic locking tab.
To install:
Snap a new bulb into the wiring harness. Make sure the locking tab is over the lock.
Install the bulb assembly by putting the small tab in the small notch in the retainer ring.
Turn the bulb assembly 1/6 turn clockwise to lock it in place
Non-European Style
Remove the headlamp trim panel attaching screws.
Remove the headlamp trim panel attaching screws
2. Remove the headlamp bulb retaining screws. Do not touch the two headlamp aiming screws, (at the top and side of the retaining ring), or the headlamp aim will have to be readjusted.
Remove the headlamp trim panel assembly from it's mounting location
3. Using a screwdriver, remove the retaininchange headlight in 1995 cutlass ciera - 1eaacc8.gifws.
change headlight in 1995 cutlass ciera - efd1171.gifcrewdriver, remove the retaining ring screws
Once the retaining ring screws are removed, the ring can be pulled away
4. Pull the bulbchange headlight in 1995 cutlass ciera - 6fe656e.giforward then separate them. Unplug the electrical connector from the rear of the bulb.
Pull the bulb out and unplug the electrical connector
To install:
Plug the new bulb into the electrical connector.
Install the bulb into the retaining ring and install the ring and bulb.
Boy nothing like an easy bulb replacement! to start off take off the side turn signals which are held together by 3 T15 screws than disconnect the bulb on that. Next remove the center grill held in place with 6 T15 1 1 1/2 screws. Now the frame from the head light can easily be accessed, look on the left and the right side of the frame and there are 2 10mm bolts, remove the 4 of them and its slides out like pie. twist out your old bulb, twist back in your new ones, reverse what I just told you to do and your finished. Could of been easier but but Oldsmobile likes to make us work I guess.
Answers & Comments
Please don't forget to rate!
- Snap a new bulb into the wiring harness. Make sure the locking tab is over the lock.
- Install the bulb assembly by putting the small tab in the small notch in the retainer ring.
- Turn the bulb assembly 1/6 turn clockwise to lock it in place
- Remove the headlamp trim panel attaching screws.
- Plug the new bulb into the electrical connector.
- Install the bulb into the retaining ring and install the ring and bulb.
- Install the trim panel.
Composite Headlights
- Open the hood.
- Turn the bulb assembly counterclockwise 1/6 turn, pressing in firmly, until the flanges align with the slots in the retainer ring.
- Pull out the bulb assembly. You may have to rock it up and down slightly to loosen it.
- Disconnect the bulb base from the harness by lifting the plastic locking tab.
To install:Non-European Style
Remove the headlamp trim panel attaching screws
2. Remove the headlamp bulb retaining screws. Do not touch the two headlamp aiming screws, (at the top and side of the retaining ring), or the headlamp aim will have to be readjusted.
Remove the headlamp trim panel assembly from it's mounting location
3. Using a screwdriver, remove the retaininchange headlight in 1995 cutlass ciera - 1eaacc8.gifws.
change headlight in 1995 cutlass ciera - efd1171.gifcrewdriver, remove the retaining ring screws
Once the retaining ring screws are removed, the ring can be pulled away
4. Pull the bulbchange headlight in 1995 cutlass ciera - 6fe656e.giforward then separate them. Unplug the electrical connector from the rear of the bulb.
Pull the bulb out and unplug the electrical connector
To install:
Boy nothing like an easy bulb replacement! to start off take off the side turn signals which are held together by 3 T15 screws than disconnect the bulb on that. Next remove the center grill held in place with 6 T15 1 1 1/2 screws. Now the frame from the head light can easily be accessed, look on the left and the right side of the frame and there are 2 10mm bolts, remove the 4 of them and its slides out like pie. twist out your old bulb, twist back in your new ones, reverse what I just told you to do and your finished. Could of been easier but but Oldsmobile likes to make us work I guess.