Remove or disconnect the following: Engine undercover Front exhaust pipe Lower oil pan bolts and lower pan Cover Upper oil pan bolt and upper pan Baffle plate
Fig. Oil pan and related components-2.0L engine
To install:
Clean all gasket surfaces of the cylinder block and the upper and lower oil pan.
Install or connect the following: Baffle plate
Apply a 0.16 in. (4mm) bead of sealant to the gasket surfaces of the upper oil pan. Upper oil pan onto the cylinder block within 15 minutes after applying sealant. Tighten the bolts as shown in the accompanying figure.
have a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f8023192d.jpgmages/0996b43f8023192d.jpg" alt="0996b43f8023192d.jpg" /> Fig. Upper oil pan bolt location and torque sequence-2.0L engine
Apply 0.16 in. (4mm) bead of sealant to the gasket surfaces of the lower oil pan. Lower oil pan and tighten the bolts, in the sequence shown, to 88-10have a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f8023192e.jpgm)
Fig. Lower oil pan bolt tightening sequence-2.0L engine Front exhaust pipe Engine undercoverhave a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f8023192f.jpgug with a new gasket and tighten to 29 ft. lbs. (40 Nm)
Fig. Make sure to the install the new drain plug gasket as shown, or leaks will occur
Lower the vehicle and fill the crankcase to the proper level with clean engine oil.
Connect the negative battery cable. Start the engine and check for leaks.
Non-Turbo Engine
Disconnect the negative battery cable.
Raise and safely support the vehicle.
Drain the engine oil into a suitable container.
Once the oil has completely drained, install the plug and tighten to 25 ft. lbs. (34 Nm).
Remove the front exhaust pipe.
Remove the engine oil dipstick and tube assembly.
Remove thave a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f80222121.jpgn>
Unfasten the oil pan mounting bolts, then remove the oil pan and gasket.
Fig. Exploded view of the oil pan and related components-1999 2.0L non-turbo engine
To install:
Apply sealant at the point where the engine block meets the oil pump.
Use a new gasket and install the oil pan. Tighten the mounting bolts to 8.9 ft. lbs. (12 Nm).
Install the front plate.
Install the front exhaust pipe.
Install the dipstick and tube assembly.
Safely lower the vehicle to the floor.
Refill the crankcase with oil to the proper level.
nnect the negative battery cable.
Start the engine and check for leaks.
Turbo Engine
Disconnect the negative battery cable.
Safely raise and support the vehicle.
Remove the front exhaust pipe.
Remove the exhaust pipe and muffler assembly.
Drain the engine oil into a suitable container. Once the oil has drained completely, tighten the plug to 29 ft. lbs. (39 Nm).
Remove the dipstick and tube.
For AWD vehicles, remove the transfer case assembly as follows:
With the propeller shaft still installed, remove the transfer mounting bolt.
Insert a suitable prytool in between the transfer case and transaxle, then remove the transfer case from the center shaft.
Remove the transfer case from the center shaft. Do NOT tilt the transfer assembly to the rear or oil will leak out.
Answers & Comments
2.0L Engine
- Disconnect the negative battery cable.
- Drain the engine oil.
- Remove or disconnect the following:
To install:
- Clean all gasket surfaces of the cylinder block and the upper and lower oil pan.
- Install or connect the following:
- Apply a 0.16 in. (4mm) bead of sealant to the gasket surfaces of the upper oil pan.
- Apply 0.16 in. (4mm) bead of sealant to the gasket surfaces of the lower oil pan.
Engine undercover Front exhaust pipe Lower oil pan bolts and lower pan Cover Upper oil pan bolt and upper pan Baffle plate
Fig. Oil pan and related components-2.0L engine
Baffle plate
Upper oil pan onto the cylinder block within 15 minutes after applying sealant. Tighten the bolts as shown in the accompanying figure.
have a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f8023192d.jpgmages/0996b43f8023192d.jpg" alt="0996b43f8023192d.jpg" /> Fig. Upper oil pan bolt location and torque sequence-2.0L engine
Lower oil pan and tighten the bolts, in the sequence shown, to 88-10have a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f8023192e.jpgm)
Fig. Lower oil pan bolt tightening sequence-2.0L engine
Front exhaust pipe Engine undercoverhave a 1999 eclipse 2.0 L...Need to replace oil pa - 0996b43f8023192f.jpgug with a new gasket and tighten to 29 ft. lbs. (40 Nm)
Fig. Make sure to the install the new drain plug gasket as shown, or leaks will occur
Fig. Exploded view of the oil pan and related components-1999 2.0L non-turbo engine
To install:
Turbo Engine