HP IQ772 power but no boot
My HP IQ772 has been working fine for 4 years and then all of a sudden it fails to boot. The computer switches on but will not boot. The screen remains blank and there is no activity from the hard disk. The LED by the multi-flashcard reader remains on and no other LEDs operate. I've tried replacing the AMD Turion X2 microprocessor and checked the hard disk etc. I've also tried reconnecting the display cable to the on-board graphics instead of the MXM graphics card. All the capacitors on the motherboard look OK and a quick check of a number of voltages on the motherboard looks OK. All the voltages out of the power supply appear correct and there are no obvious bad capacitors in the power supply. I've also changed the CMOS backup battery. Can anyone offer any help with repairing this PC?
Computers & Internet - HP - TouchSmart
Answers & Comments
This post is 2011
fixha had brainfartt.
Dude - OLD thread, nobody cares!!
All PC's fail. (Virus is #1 )
Turn on the computer and press the F8 key repeatedly as the computer starts. An "Advanced Boot Options" screen opens.
Select Repair Your Computer and press Enter . Select a keyboard layout that matches your country/region and click Next . When the login prompt appears, select the user name with Administrator rights (not Administrator) from the User Name drop down. The user name with Admistrator rights is most likely the first user name that was entered during the initial computer setup. Type the logon password into the Password field (press Enter if you didn't put in a password) and then click OK .
Click Command Prompt . At the prompt enter: c: At the c prompt, enter: chkdsk /b If a message opens saying you need to forcibly dismount the drive say yes. When it is done, try to do an F11 recovery again.
what OS (xp,vista, w7) ?
is this PC in UK, England?
HP shows, CIRCA 2007 build, (1st) and is near out of support)
sure... you skipped the first steps.
1: battery out, get it out of the pc.
2: use only he a.c line pack ,
3 it has PSU are all power pins reading correct voltage? must
4: if above ok, the BIOS works, on all systems,
GET BIOS to work first.
do you know your BIOS hot keys, its very important to learn this first
if working on any PC made ever. 1981 to now.
see this yet, the BOOKS
http://support.hp.com/us-en/product/HP%20TouchSmart%20IQ700%20Desktop%20PC%20series/3351217/model/3561184/manuals?jumpid=reg_r1002_usen_s-001_title_r0001
best is not to pull any Cmos battery , just use a volt meter
there, 3v is good, 2v bad. see? or scramble all BIOS setting
including boot drive... arg.
this box has no standard VGA 15pin jack on rear, making
tests with external display hard
use a flashlight pointed at screen see any >Turn off the computer and wait at least 5 seconds with the computer in a full off state.
A System Recovery Options window opens.
black screen has many causes.
if its not just the back light dead, use a flash light first
get BIOS to work, do you get F8 or F11 screens
this is key to solving the true cause on all PCs.
one can use a USB keyboard if yous dies.
ask here , on the real forum.
http://h30434.www3.hp.com/t5/Desktop-Video-Display-and-Touch/IQ772-Boot-Up-Problems/td-p/64527
i read your 2 users guides, no one word on BIOS
that is BS. and due to now rear VGA port (has some mini bs jack)
you cant see if the PC is dead or just the silly display or GPU chip dead.,
a preplexing box, i never buy those i get real DT or top HP laptops.
all in one boxes are custom, and tricky to fix.
for sure the nasty VGA trick missing, JACK