For that Connect your router to computer with ethernet cable then you can access it with following default link. http://192.168.0.1 or http://192.168.1.1If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it. Then it ask for user name and password. Type user as "admin" and password as "admin" or "password" or blank. Then you can see configuration page of router.
I hate to say this but the Blitz router was forced to discontinue sales because it performed beyond the limits allowed by the FCC (in other words it worked better than the FCC allows) the Blitz website is still there but no information is available for it or it's routers. Fortunately I have one of these routers and love it because it out performs even the newer routers I have bought, I also needed to get into the online setup for the router and had the same problem, would press the reset button and type in "admin" for both user and password and received an error. So I thought I would take it apart and see if I could remove the eprom and reprogram the password by bypassing the electronics of the router, but when I opened the router I found that the company used a older memory chip to store the configurations in and even that this older chip was very stable and more than fast enough for the router, this older chip required quite a heavy rest signal to reset the memory, so I tried resetting the router with adding five seconds to each reset attempt and I found that a partial reset happened at 25 seconds and a full reset was obtained at 30 seconds. So what does this mean? Simply it means to reset this router you must press and hold the reset button for 30 seconds or longer to get the router to reset to it's original factory settings, I use 35 seconds and it has worked every time I have done it. So to reset the Blitz router you need to press and hold the reset button for 35 seconds then release it and allow it to boot up, then use your browser and use the address 192.168.1.1 (the factory default) and when the screen comes up use "admin" (without the " ") for both the user name and password and your able to then reset the password and user name and any other settings you need to use. NOTE: you must use a direct wired connection to access the router when reset to the factory defaults because the defaults will not allow wireless access to the router, until you turn on the wireless function in the setup screens for the router configurations. If you have any other problems email me at versitalbear at yahoo dot com (I spelled my email out because email spiders and web bots cannot detect the email for spam lists) I have since bought four more of these routers, used, simply because they are really great routers and have one of the most powerful radio circuits of any router I have seen or bought, typically I get twice the range, of most other routers, with the Blitz, They are very good routers, hang on to yours.
Answers & Comments
For that Connect your router to computer with ethernet cable then you can access it with following default link.
http://192.168.0.1
or
http://192.168.1.1If you are not able to access it with above ip then check your computers ip address gateway ip is your router ip try with it.
Then it ask for user name and password.
Type user as "admin" and password as "admin" or "password" or blank.
Then you can see configuration page of router.
I hate to say this but the Blitz router was forced to discontinue sales because it performed beyond the limits allowed by the FCC (in other words it worked better than the FCC allows) the Blitz website is still there but no information is available for it or it's routers.
Fortunately I have one of these routers and love it because it out performs even the newer routers I have bought, I also needed to get into the online setup for the router and had the same problem, would press the reset button and type in "admin" for both user and password and received an error. So I thought I would take it apart and see if I could remove the eprom and reprogram the password by bypassing the electronics of the router, but when I opened the router I found that the company used a older memory chip to store the configurations in and even that this older chip was very stable and more than fast enough for the router, this older chip required quite a heavy rest signal to reset the memory, so I tried resetting the router with adding five seconds to each reset attempt and I found that a partial reset happened at 25 seconds and a full reset was obtained at 30 seconds.
So what does this mean? Simply it means to reset this router you must press and hold the reset button for 30 seconds or longer to get the router to reset to it's original factory settings, I use 35 seconds and it has worked every time I have done it.
So to reset the Blitz router you need to press and hold the reset button for 35 seconds then release it and allow it to boot up, then use your browser and use the address 192.168.1.1 (the factory default) and when the screen comes up use "admin" (without the " ") for both the user name and password and your able to then reset the password and user name and any other settings you need to use.
NOTE: you must use a direct wired connection to access the router when reset to the factory defaults because the defaults will not allow wireless access to the router, until you turn on the wireless function in the setup screens for the router configurations.
If you have any other problems email me at versitalbear at yahoo dot com (I spelled my email out because email spiders and web bots cannot detect the email for spam lists) I have since bought four more of these routers, used, simply because they are really great routers and have one of the most powerful radio circuits of any router I have seen or bought, typically I get twice the range, of most other routers, with the Blitz, They are very good routers, hang on to yours.