Thanks for reply. Below are info about programming mode.. PROGRAMMING MODE Keep your remote control aimed at the device you want to control during this process. The remote control will send out the “power” command for the device being programmed. While holding down the device key (i.e., TV) that you are programming, press the “Mute” key for one full second. Then release the keys. The device key should light and stay lit. If it doesn’t, repeat the process. Then choose either the code scan or code entry method.
CODE SCAN Once you are in programming mode, repeatedly tap the CH-UP key to step through the codes, sending out the power command. This could take some time since there are could be many for each type of device. When your device shuts off, you have found the code. If you inadvertently go past a code that responded, or realized that you may not have been aiming the remote at the device, you can use the CH-DOWN key to step backward through the codes. Press the POWER key to verify that you haven’t missed the code. In order to lock in the code, press the device key again. The remote will remember the code until you reprogram it.
CODE ENTRY First, look up the device type and brand in the following charts. You will find a list of numbers; one or more of which should operate your device. If there is more than one code, you will need to try each of them to find the one that works best. Once you are in code entry mode, enter the three-digit code. Press the device key being programmed once again to lock in the entered code. The remote will remember the code until you reprogram it.
Hope that will help. Thanks.
Thanks. How do I get into the programming mode. Good Service. John Stubbs
Thanks for reply. Below are info about programming mode.. PROGRAMMING MODE Keep your remote control aimed at the device you want to control during this process. The remote control will send out the “power” command for the device being programmed. While holding down the device key (i.e., TV) that you are programming, press the “Mute” key for one full second. Then release the keys. The device key should light and stay lit. If it doesn’t, repeat the process. Then choose either the code scan or code entry method.
CODE SCAN Once you are in programming mode, repeatedly tap the CH-UP key to step through the codes, sending out the power command. This could take some time since there are could be many for each type of device. When your device shuts off, you have found the code. If you inadvertently go past a code that responded, or realized that you may not have been aiming the remote at the device, you can use the CH-DOWN key to step backward through the codes. Press the POWER key to verify that you haven’t missed the code. In order to lock in the code, press the device key again. The remote will remember the code until you reprogram it.
CODE ENTRY First, look up the device type and brand in the following charts. You will find a list of numbers; one or more of which should operate your device. If there is more than one code, you will need to try each of them to find the one that works best. Once you are in code entry mode, enter the three-digit code. Press the device key being programmed once again to lock in the entered code. The remote will remember the code until you reprogram it.
Answers & Comments
Hi,
Remote codes for Sony TV are as follows...
001, 085, 126, 166, 079
Click HERE to download Instruction Manual of HRMC-5, please check page 8-2 for remote codes in manual.
Thanks.
Thanks. How do I get into the programming mode.
Good Service.
John Stubbs
================================================================
Thanks for reply. Below are info about programming mode..
PROGRAMMING MODE
Keep your remote control aimed at the device you want to control during this
process. The remote control will send out the “power” command for the
device being programmed.
While holding down the device key (i.e., TV) that you are programming,
press the “Mute” key for one full second. Then release the keys. The device
key should light and stay lit. If it doesn’t, repeat the process.
Then choose either the code scan or code entry method.
CODE SCAN
Once you are in programming mode, repeatedly tap the CH-UP key to step
through the codes, sending out the power command. This could take some
time since there are could be many for each type of device. When your device
shuts off, you have found the code. If you inadvertently go past a code that
responded, or realized that you may not have been aiming the remote at the
device, you can use the CH-DOWN key to step backward through the codes. Press the POWER
key to verify that you haven’t missed the code. In order to lock in the
code, press the device key again. The remote will remember the code until
you reprogram it.
CODE ENTRY
First, look up the device type and brand in the following charts. You will find
a list of numbers; one or more of which should operate your device. If there is
more than one code, you will need to try each of them to find the one that
works best.
Once you are in code entry mode, enter the three-digit code. Press the device
key being programmed once again to lock in the entered code. The remote
will remember the code until you reprogram it.
Hope that will help.
Thanks.