There is a low voltage on the projection that sometime cannot be filtered, some cases can be solve by upluging to the wall outlet then replug it again.
and then test.
But if this not solve you should test the horizontal and veritical cercuit to check the voltage regulator in it.
To do a hard restet is to take the power cord/cable off from the wall socket and leave the tv turned off for atleat 2 hrs then reconnect and see the status. post me the status.
To do a hard restet is to take the power cord/cable off from the wall socket and leave the tv turned off for atleat 2 hrs then reconnect and see the status. post me the status.
Replace the DLP lamp out of your Zenith or LG, you will need to reset the counter…otherwise you may get an annoying reminder every few days if you’re surpassed the predetermined hour mark.
To Reset:
Ensure the TV is powered on.
1) Press and HOLD the MENU button on the TV
2) Press and HOLD the MENU button on your REMOTE
(hold both these until the service menu pops up 5-10 secs max.)
3) Let go of the REMOTE button first, then release the button on the TV
4) Press and HOLD the ENTER (or OK) button on the TV
5) Press and HOLD the MUTE button on the REMOTE
(hold both until the LAMP LIFE HOURS appears on the screen)
6) Let go of the REMOTE button first, then release the button on the TV
We suggest writing your lamp hours on a peice of masking tape and taping it to the back the TV for future reference.
7) To reset the lamp counter, press SELECT (or the button in the middle of the direction arrove buttons). Hit SELECT a second time to confirm clearing the lamp counter
For certain models, you might have to tweak these steps slightly…offer your inputs!
Replace the DLP lamp out of your Zenith or LG, you will need to reset the counter…otherwise you may get an annoying reminder every few days if you’re surpassed the predetermined hour mark. To Reset: Ensure the TV is powered on. 1) Press and HOLD the MENU button on the TV 2) Press and HOLD the MENU button on your REMOTE (hold both these until the service menu pops up 5-10 secs max.) 3) Let go of the REMOTE button first, then release the button on the TV 4) Press and HOLD the ENTER (or OK) button on the TV 5) Press and HOLD the MUTE button on the REMOTE (hold both until the LAMP LIFE HOURS appears on the screen) 6) Let go of the REMOTE button first, then release the button on the TV We suggest writing your lamp hours on a peice of masking tape and taping it to the back the TV for future reference. 7) To reset the lamp counter, press SELECT (or the button in the middle of the direction arrove buttons). Hit SELECT a second time to confirm clearing the lamp counter For certain models, you might have to tweak these steps slightly…offer your inputs!
Answers & Comments
Hello,
There is a low voltage on the projection that sometime cannot be filtered, some cases can be solve by upluging to the wall outlet then replug it again.
and then test.
But if this not solve you should test the horizontal and veritical cercuit to check the voltage regulator in it.
warning-high voltage inside the TV.
melnavz
Try to do a hard reset first and let me know the status
To do a hard restet is to take the power cord/cable off from the wall socket and leave the tv turned off for atleat 2 hrs then reconnect and see the status.
post me the status.
Replace the DLP lamp out of your Zenith or LG, you will need
to reset the counter…otherwise you may get an annoying reminder every
few days if you’re surpassed the predetermined hour mark.
To Reset:
Ensure the TV is powered on.
1) Press and HOLD the MENU button on the TV
2) Press and HOLD the MENU button on your REMOTE
(hold both these until the service menu pops up 5-10 secs max.)
3) Let go of the REMOTE button first, then release the button on the TV
4) Press and HOLD the ENTER (or OK) button on the TV
5) Press and HOLD the MUTE button on the REMOTE
(hold both until the LAMP LIFE HOURS appears on the screen)
6) Let go of the REMOTE button first, then release the button on the TV
We suggest writing your lamp hours on a peice of masking tape and taping it to the back the TV for future reference.
7) To reset the lamp counter, press SELECT (or the button in the middle
of the direction arrove buttons). Hit SELECT a second time to confirm
clearing the lamp counter
For certain models, you might have to tweak these steps slightly…offer your inputs!
Some transitor is gone bad,you better send it for repair