All modern vehicles are equipped with an onboard computer diagnostic system (OBDII) that constantly monitors your vehicle's major operating systems and most importantly the power-train (engine and transmission). The main purpose of monitoring these systems is to insure that the vehicle is operating at top efficiency with the lowest possible emissions. As fuel economy and emission control has become increasingly important and complex, your vehicle's electronics systems need to constantly adjust and fine-tune various parameters according to driving conditions (such as vehicle load, temperature, and air/fuel mix to name just a few). When the computer reads that any of these parameters do not fall within the acceptable range for operating the vehicle, your CHECK ENGINE LIGHT is lit to warn you that you may have a serious problem and to take your vehicle to a certified technician - such as your local AAMCO technician - to check the faults and restore it to manufacturer's specifications.
If the check-engine light comes on, here are some tips on what you should do: - Look for a serious problem that requires immediate attention. Check your dashboard gauges and lights for indications of low oil pressure or overheating. These conditions mean you should pull over and shut off the engine as soon as you can find a safe place to do so. On some cars, a yellow "check engine" means investigate the problem, while a red "check engine" means stop right now. - Try tightening your gas cap. This often solves the problem. Keep in mind that it may take several trips before the light resets. Some vehicles have a separate indicator that warns of a loose gas cap before the condition sets off the "check engine" light. - Reduce speed and load. If the "check engine" light is blinking or you notice any serious performance problems, such as a loss of power, reduce your speed and try to reduce the load on the engine. For example, it would be a good idea to stop towing a trailer. Have the car checked as soon as possible to prevent expensive damage. - Contact OnStar, if available. If you have a 1997 or later General Motors vehicle equipped with OnStar and an active OnStar subscription, contact an advisor who can read the trouble code remotely and advise you about what to do. - Have the code read and the problem fixed. If you want to diagnose the malfunction yourself, you can buy a scan tool at most auto parts stores. Prices range from about $40 to several hundred, depending on the model and the features. The tools come with instructions on how to hook them up and decipher the codes. But unless you have a good knowledge of automotive diagnostics, you're probably better off taking the vehicle to a professional. Some automotive parts stores will read and interpret the code for you without charge. Unless there is an easy fix, they may simply refer you to a mechanic. - Don't go for a state emissions test. In a late-model car, an illuminated "check engine" light probably is a sure sign your car will fail the test. In some states, it's an automatic failure, even if the problem was nothing more than a loose gas cap. By the way, don't bother trying to fool the inspection station by disconnecting the battery or using any other method to erase the trouble code and turn off the "check engine" light. Your vehicle's computer will let the inspection station know that its codes have been erased, and you'll just have to go back again.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Answers & Comments
All modern vehicles are equipped with an onboard computer diagnostic system (OBDII) that constantly monitors your vehicle's major operating systems and most importantly the power-train (engine and transmission). The main purpose of monitoring these systems is to insure that the vehicle is operating at top efficiency with the lowest possible emissions. As fuel economy and emission control has become increasingly important and complex, your vehicle's electronics systems need to constantly adjust and fine-tune various parameters according to driving conditions (such as vehicle load, temperature, and air/fuel mix to name just a few). When the computer reads that any of these parameters do not fall within the acceptable range for operating the vehicle, your CHECK ENGINE LIGHT is lit to warn you that you may have a serious problem and to take your vehicle to a certified technician - such as your local AAMCO technician - to check the faults and restore it to manufacturer's specifications.
If the check-engine light comes on, here are some tips on what you should do:
- Look for a serious problem that requires immediate attention. Check your dashboard gauges and lights for indications of low oil pressure or overheating. These conditions mean you should pull over and shut off the engine as soon as you can find a safe place to do so. On some cars, a yellow "check engine" means investigate the problem, while a red "check engine" means stop right now.
- Try tightening your gas cap. This often solves the problem. Keep in mind that it may take several trips before the light resets. Some vehicles have a separate indicator that warns of a loose gas cap before the condition sets off the "check engine" light.
- Reduce speed and load. If the "check engine" light is blinking or you notice any serious performance problems, such as a loss of power, reduce your speed and try to reduce the load on the engine. For example, it would be a good idea to stop towing a trailer. Have the car checked as soon as possible to prevent expensive damage.
- Contact OnStar, if available. If you have a 1997 or later General Motors vehicle equipped with OnStar and an active OnStar subscription, contact an advisor who can read the trouble code remotely and advise you about what to do.
- Have the code read and the problem fixed. If you want to diagnose the malfunction yourself, you can buy a scan tool at most auto parts stores. Prices range from about $40 to several hundred, depending on the model and the features. The tools come with instructions on how to hook them up and decipher the codes. But unless you have a good knowledge of automotive diagnostics, you're probably better off taking the vehicle to a professional. Some automotive parts stores will read and interpret the code for you without charge. Unless there is an easy fix, they may simply refer you to a mechanic.
- Don't go for a state emissions test. In a late-model car, an illuminated "check engine" light probably is a sure sign your car will fail the test. In some states, it's an automatic failure, even if the problem was nothing more than a loose gas cap. By the way, don't bother trying to fool the inspection station by disconnecting the battery or using any other method to erase the trouble code and turn off the "check engine" light. Your vehicle's computer will let the inspection station know that its codes have been erased, and you'll just have to go back again.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day.