Please let me talk to some one that has installed the python 991. I have a rpn 7752p remote that is not on the list that the so called experts have referred me to. All I need is the step it takes to pair the remote to the receiver
Vehicle Parts & Accessories - Python - 991 Responder LC3 SST Security/Remote Start System
Here is the learn routine for Python 99# series alarms; it is used to add transmitters or to change button assignments if paired transmitters.
Note: The learn routine may be locked if previously programmed using the Bitwriter. This is done to make your system safer from 'educated' thieves, but is not usually done by the average shop. If the horn generates one long honk when attempting to program the unit, the learn routine is locked and must be unlocked using the Bitwriter before proceeding. So you'll need to go to a shop, or buy yourself a Bitwriter. (I gather many shops don't even charge for this service, since a happy client is likely to come back and buy more gear.)
The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit: Door, Key, Choose, Transmit and Release.
1. Open a door. (The GREEN wire, H1/8, or the VIOLET, H1/6 must be connected.) 2. Key. Turn the ignition to the ON position. 3. Choose. Within 10 seconds, press and release the Program switch the number of times corresponding to the desired channel listed below. Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and the horn will honk (if connected) to confirm the selected channel. Do not release the Program switch. 4. Transmit. While HOLDING the Valet/Program switch, press the button on the transmitter that you would like to control the selected receiver channel. The unit will chirp to confirm that the code has been successfully programmed. 5. Release. Once the code is learned, the Valet/Program switch can be released. Your new remote is now paired.
Python Channel List:
1 Auto Learn Standard Configuration* (default) 2 Arm only 3 Disarm only 4 Silent Mode™/Remote Valet/Trunk Release RED/WHITE 5 Remote Start 6 Channel 4 VIOLET/BLACK 7 Channel 5 WHITE/BLACK 8 Channel 6 9 Short Run/Turbo 10 Timer Mode 11 Arm/Disarm/Panic 12 Panic only 13 Defogger Control 14 Delete all transmitters**
Channel 1 is what you want.
You can advance from programming one channel to another by releasing the Valet/Program switch and tapping it to advance channels and then HOLDING it. For instance: You have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash two times and the horn will honk twice (if connected). As before, do not release it. If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will honk three times (if connected) and the LED will flash three times to confirm it is ready to receive the code from the transmitter.
Answers & Comments
Here is the learn routine for Python 99# series alarms; it is used to add transmitters or to change button assignments if paired transmitters.
Note: The learn routine may be locked if previously programmed using the Bitwriter. This is done to make your system safer from 'educated' thieves, but is not usually done by the average shop. If the horn generates one long honk when attempting to program the unit, the learn routine is locked and must be unlocked using the Bitwriter before proceeding. So you'll need to go to a shop, or buy yourself a Bitwriter. (I gather many shops don't even charge for this service, since a happy client is likely to come back and buy more gear.)
The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit: Door, Key, Choose, Transmit and Release.
1. Open a door. (The GREEN wire, H1/8, or the VIOLET, H1/6 must be connected.)
2. Key. Turn the ignition to the ON position.
3. Choose. Within 10 seconds, press and release the Program switch the number of times corresponding to the desired channel listed below. Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and the horn will honk (if connected) to confirm the selected channel. Do not release the Program switch.
4. Transmit. While HOLDING the Valet/Program switch, press the button on the transmitter that you would like to control the selected receiver channel. The unit will chirp to confirm that the code has been successfully programmed.
5. Release. Once the code is learned, the Valet/Program switch can be released. Your new remote is now paired.
Python Channel List:
1 Auto Learn Standard Configuration* (default)
2 Arm only
3 Disarm only
4 Silent Mode™/Remote Valet/Trunk Release RED/WHITE
5 Remote Start
6 Channel 4 VIOLET/BLACK
7 Channel 5 WHITE/BLACK
8 Channel 6
9 Short Run/Turbo
10 Timer Mode
11 Arm/Disarm/Panic
12 Panic only
13 Defogger Control
14 Delete all transmitters**
Channel 1 is what you want.
You can advance from programming one channel to another by releasing the Valet/Program switch and tapping it to advance channels and then HOLDING it. For instance: You have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash two times and the horn will honk twice (if connected). As before, do not release it. If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will honk three times (if connected) and the LED will flash three times to confirm it is ready to receive the code from the transmitter.
I hope that helps.