Did anyone ever figure it out? I can’t get it back in either. Got this for 10$ and the machine was brand new. Figured it would be good to start with but the thread keeps bird nesting on the bottom. Tried adjusting tension, rethreading.. now I just took case out to tighten screw for the bobbins tension and cant get it back in. Thinking about throwing in the towel and buying a better machine.
Tina wondering if you ever found an answer...I'm having the same issue with mine and no one seems to understand the question..just can't get it back into the machine
This doesn't really address the problem. The question is not about the bobbin itself. It is about the Bobbin CASE. The case has popped out and I can't figure out how to put it back in. The machine is all plastic and I don't want to try to force it back in because it may break. The instruction manual is no help really. It shows you what position the case should be in, but it doesn't tell you how to put it in. For example, does the needle need to be in an up position, do I need to put it in at an angle, if so tilted in what direction, etc.?
These answers don't really address the problem. The question is not about the bobbin itself. It is about the Bobbin CASE. The case is the part that holds the bobbin in the right place so the upper thread passes over the bobbin in just the right way to pick up the bobbn thread and create a stitch. The case has popped out and I can't figure out how to put it back in. The machine is all plastic and I don't want to try to force it back in because it may break. The instruction manual is no help really. It shows you what position the case should be in once it is in the machine, but it doesn't tell you how to put it in. For example, does the needle need to be in an up position, do I need to put it in at an angle, if so tilted in what direction, etc.? These answers don't really address the problem. The question is not about the bobbin itself. It is about the Bobbin CASE. The case is the part that holds the bobbin in the right place so the upper thread passes over the bobbin in just the right way to pick up the bobbn thread and create a stitch. The case has popped out and I can't figure out how to put it back in. The machine is all plastic and I don't want to try to force it back in because it may break. The instruction manual is no help really. It shows you what position the case should be in once it is in the machine, but it doesn't tell you how to put it in. For example, does the needle need to be in an up position, do I need to put it in at an angle, if so tilted in what direction, etc.?
Did you ever figure out how to put it back, Mine just popped out and its very frustrating.Did you ever figure out how to put it back, Mine just popped out and its very frustrating.
Answers & Comments
Did anyone ever figure it out? I can’t get it back in either. Got this for 10$ and the machine was brand new. Figured it would be good to start with but the thread keeps bird nesting on the bottom. Tried adjusting tension, rethreading.. now I just took case out to tighten screw for the bobbins tension and cant get it back in. Thinking about throwing in the towel and buying a better machine.
Tina wondering if you ever found an answer...I'm having the same issue with mine and no one seems to understand the question..just can't get it back into the machine
This doesn't really address the problem. The question is not about the bobbin itself. It is about the Bobbin CASE. The case has popped out and I can't figure out how to put it back in. The machine is all plastic and I don't want to try to force it back in because it may break. The instruction manual is no help really. It shows you what position the case should be in, but it doesn't tell you how to put it in. For example, does the needle need to be in an up position, do I need to put it in at an angle, if so tilted in what direction, etc.?
These answers don't really address the problem. The question is not about the bobbin itself. It is about the Bobbin CASE. The case is the part that holds the bobbin in the right place so the upper thread passes over the bobbin in just the right way to pick up the bobbn thread and create a stitch. The case has popped out and I can't figure out how to put it back in. The machine is all plastic and I don't want to try to force it back in because it may break. The instruction manual is no help really. It shows you what position the case should be in once it is in the machine, but it doesn't tell you how to put it in. For example, does the needle need to be in an up position, do I need to put it in at an angle, if so tilted in what direction, etc.?
Did you ever figure out how to put it back, Mine just popped out and its very frustrating.