It sounds like the engine runs fine in the cold or open loop mode, but when it switches to closed loop it stalls due to bad sensor information. Your codes are detailed below.
Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Open fuse
Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Update control unit software - Check for the latest control unit update Powertrain or Engine Control Module faulty
DTC Code: P0340 Description: Camshaft Position Sensor A Circuit (Bank 1 Or Single Sensor) Probable Causes:
Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Update control unit software - Check for the latest control unit update Powertrain or Engine Control Module faulty
DTC Code: P1320 Description: Ign Signal Primary Probable Causes:
Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Update control unit software - Check for the latest control unit update Powertrain or Engine Control Module faultyIt sounds like the engine runs fine in the cold or open loop mode, but when it switches to closed loop it stalls due to bad sensor information. Your codes are detailed below. DTC Code: P0135 Description: Oxygen Sensor Heater Circuit (Bank 1, Sensor 1) Probable Causes: Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Open fuse DTC Code: P0325 Description: Knock Sensor 1 Circuit (Bank 1) Probable Causes: Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Update control unit software - Check for the latest control unit update Powertrain or Engine Control Module faulty DTC Code: P0340 Description: Camshaft Position Sensor A Circuit (Bank 1 Or Single Sensor) Probable Causes: Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Update control unit software - Check for the latest control unit update Powertrain or Engine Control Module faulty DTC Code: P1320 Description: Ign Signal Primary Probable Causes: Sensor or solenoid faulty Connector terminal contact is damaged or corroded Wire harness - Check harness for correct voltage, open, short to ground or short to voltage Update control unit software - Check for the latest control unit update Powertrain or Engine Control Module faulty
Answers & Comments
Does then engine show any codes? some auto part stores will check your vehicle for no charge.
It sounds like the engine runs fine in the cold or open loop mode, but when it switches to closed loop it stalls due to bad sensor information. Your codes are detailed below.
DTC Code: P0135
Description: Oxygen Sensor Heater Circuit (Bank 1, Sensor 1)
Probable Causes:
Sensor or solenoid faulty
Connector terminal contact is damaged or corroded
Wire harness - Check harness for correct voltage, open, short to ground or short to voltage
Open fuse
DTC Code: P0325
Description: Knock Sensor 1 Circuit (Bank 1)
Probable Causes:
Sensor or solenoid faulty
Connector terminal contact is damaged or corroded
Wire harness - Check harness for correct voltage, open, short to ground or short to voltage
Update control unit software - Check for the latest control unit update
Powertrain or Engine Control Module faulty
DTC Code: P0340
Description: Camshaft Position Sensor A Circuit (Bank 1 Or Single Sensor)
Probable Causes:
Sensor or solenoid faulty
Connector terminal contact is damaged or corroded
Wire harness - Check harness for correct voltage, open, short to ground or short to voltage
Update control unit software - Check for the latest control unit update
Powertrain or Engine Control Module faulty
DTC Code: P1320
Description: Ign Signal Primary
Probable Causes:
Sensor or solenoid faulty
Connector terminal contact is damaged or corroded
Wire harness - Check harness for correct voltage, open, short to ground or short to voltage
Update control unit software - Check for the latest control unit update
Powertrain or Engine Control Module faulty