The warm and cold air circuits cross inside the heat exchanger, which results in a thermal exchange which condenses the humidity contained in the warm air. The condensation which forms in the heat exchanger is collected in a sump, from which it falls by gravity into a tank. When the water in the tank reaches the max. level, the level of the water in the sump increases, which causes the float to move upwards, thus actioning a microswitch; The microswitch for dryers with electronic board sends a signal to the electronic circuit when the tank has been filled, switches off the appliance and lights a pilot lamp which indicates to the user that the tank is full. The microswitch with electromechanical control switches off the dryer (the timer motor is powered and ends its cycle) and lights a pilot lamp which indicates to the user that the tank is full. The tank capacity is about 3.5 lt., enough for a drying cycle.
- Remove the screw (1) which secures the support micro and use a screwdriver for the two hooks which secure it to the sump.
- Lift them simultaneously and unthread the micro support towards outside
Putting upside down the support you can access tthe full tank light remains on even though the tan - 25069013-hcssld2gpo2sm22yg24xoxcy-3-9.jpg"/uploads/images/25069013-hcssld2gpo2sm22yg24xoxcy-3-9.jpg" alt="25069013-hcssld2gpo2sm22yg24xoxcy-3-9.jpg" /> Inside the sump there is the float. To extract it rotate the float 90° clockwise as shthe full tank light remains on even though the tan - 25069013-hcssld2gpo2sm22yg24xoxcy-3-14.jpgutside and extract it.
While reassembling the pump, the float and the tank microswitch, repeat the same operations backwards, paying attention that when the micro support is remounted it is necessary to use a screwdriver in the fissure (indicated by the arrow), to lift the micro lever and lean it over the float (if this operation is not carriethe full tank light remains on even though the tan - 25069013-hcssld2gpo2sm22yg24xoxcy-3-20.jpggside the float (it deforms) and the two components do not function anymore.
Answers & Comments
The warm and cold air circuits cross inside the heat exchanger, which results in a thermal exchange which condenses the humidity contained in the warm air. The condensation which forms in the heat exchanger is collected in a sump, from which it falls by gravity into a tank. When the water in the tank reaches the max. level, the level of the water in the sump increases, which causes the float to move upwards, thus actioning a microswitch; The microswitch for dryers with electronic board sends a signal to the electronic circuit when the tank has been filled, switches off the appliance and lights a pilot lamp which indicates to the user that the tank is full. The microswitch with electromechanical control switches off the dryer (the timer motor is powered and ends its cycle) and lights a pilot lamp which indicates to the user that the tank is full.
The tank capacity is about 3.5 lt., enough for a drying cycle.
- Remove the screw (1) which secures the support micro and use a screwdriver for the two hooks which secure it to the sump.
- Lift them simultaneously and unthread the micro support towards outside
Putting upside down the support you can access tthe full tank light remains on even though the tan - 25069013-hcssld2gpo2sm22yg24xoxcy-3-9.jpg"/uploads/images/25069013-hcssld2gpo2sm22yg24xoxcy-3-9.jpg" alt="25069013-hcssld2gpo2sm22yg24xoxcy-3-9.jpg" /> Inside the sump there is the float.
To extract it rotate the float 90° clockwise as shthe full tank light remains on even though the tan - 25069013-hcssld2gpo2sm22yg24xoxcy-3-14.jpgutside and extract it.
While reassembling the pump, the float and the tank microswitch, repeat the same operations backwards, paying attention that when the micro support is remounted it is necessary to use a screwdriver in the fissure (indicated by the arrow), to lift the micro lever and lean it over the float (if this operation is not carriethe full tank light remains on even though the tan - 25069013-hcssld2gpo2sm22yg24xoxcy-3-20.jpggside the float (it deforms) and the two components do not function anymore.
Dado