The minute on T1 is one minute faster than on T2 (ie. the second time zone). How to adjust? E.g. it is now 19:44 in T1, and I want it to be 12:44 in T2, but T2 is showing 12:43
Watches - Tissot - T - T-Touch T33159851 Wrist Watch
Press the center pusher and then tap the center of the touch sensitive glass until the digital display reads either 24h/cm or 12h/ft (or any combination between the two).
Next, press and hold the center pusher in until the the digital display reads SYNCHRO.
When the display reads SYNCHRO, the watch is now ready to receive new information about where the hands are pointed. The next step, then, is to align both of the hands at precisely 12 o’clock, which is where the microprocessor expects them to be pointed when in SYNCHRO mode.
To advance the minute hand, press the pusher that is located at 2 o’clock.
To advance the hour hand, use the 4 o’clock pusher.
If you accidentally pass the 12 o’clock marker for either hand, you will have to move the hand completely around the dial again until you get it right.
Once both hands are aligned at 12 o’clock, press the center pusher to register the new settings.
First I thought that I will give you the settings of display settings but Here is the link from where you can download your watchs manual and set whatever you like compas display alzimuth whatever you like.
I already have read the manual many times before I post the question. I appreciate your help but it's not the answer I want. Thanks anyway.I already have read the manual many times before I post the question. I appreciate your help but it's not the answer I want. Thanks anyway.
Hello,kindly pull out the crown at the middle of the crowns beside the tissot watch to set the time zone of the T2..you can kindly follow the instruction provided below in the site. http://www.tissot.ch/virtualdata/usersmanual/123-en.pdf
I have the exact same problem. Found a few people who have same problem posted but there were no solution so far. Icily keep looking. In case you find the solution, kindly update . Thanks.I have the exact same problem. Found a few people who have same problem posted but there were no solution so far. Icily keep looking. In case you find the solution, kindly update . Thanks.
Answers & Comments
To re-calibrate the hands:
- Press the center pusher and then tap the center of the touch sensitive glass until the digital display reads either 24h/cm or 12h/ft (or any combination between the two).
- Next, press and hold the center pusher in until the the digital display reads SYNCHRO.
- When the display reads SYNCHRO, the watch is now ready to receive new information about where the hands are pointed. The next step, then, is to align both of the hands at precisely 12 o’clock, which is where the microprocessor expects them to be pointed when in SYNCHRO mode.
- To advance the minute hand, press the pusher that is located at 2 o’clock.
- To advance the hour hand, use the 4 o’clock pusher.
- If you accidentally pass the 12 o’clock marker for either hand, you will have to move the hand completely around the dial again until you get it right.
- Once both hands are aligned at 12 o’clock, press the center pusher to register the new settings.
First I thought that I will give you the settings of display settings but Here is the link from where you can download your watchs manual and set whatever you like compas display alzimuth whatever you like.
I already have read the manual many times before I post the question. I appreciate your help but it's not the answer I want. Thanks anyway.
Hello,kindly pull out the crown at the middle of the crowns beside the tissot watch to set the time zone of the T2..you can kindly follow the instruction provided below in the site.
http://www.tissot.ch/virtualdata/usersmanual/123-en.pdf
www.tissot.ch/virtualdata/usersmanual/123-en.pdf
www.tissot.ch/data/usersmanual/142-en.pdf
wish you good luck,
take care.
Thanks but my watch is the T Touch Expert.
I have the exact same problem. Found a few people who have same problem posted but there were no solution so far. Icily keep looking. In case you find the solution, kindly update . Thanks.