ZX-6R Ninja - Fix products instructions anything

ZX-6R Ninja Owners Manuals, User Guides, Instructional Help Documents & Information.

Featured Questions

Preliminary list of posts to be most interested community
1999 Kawasaki ZX-6R Ninja overheating
Answer
Headlights and tailight are out it is not the fuse or the switch on a 2001 kawasaki zx6r
Answer
Hi, can you tel me what size hex socket i need to remove the front wheel on my kawasaki zx6r g1
Answer
1998 Kawasaki ZX-6R Ninja will not rev up past 6,000 rpm
Answer
Its a 99 ninja not a 97. cant find where to edit question lol
Answer
What year model is this vin no please ZX 600E004957 thank you
Answer
Zx6r erratic throttle
Answer
Main and big end bearing torque - 1997 kawasaki ZX-6R Ninja
Answer
1994 Kawasaki ZX-6R Ninja firing order
Answer
1998 Kawasaki ZX-6R Ninja sprocket torque specs
Answer
2001 Kawasaki ZX-6R Ninja will not turn over
Answer
What could be the problem that there is no 5th gear on my 1996 Kawa ZX6R
Answer

Latest Questions

Latest posts in community
Trouble starting engine like if gas is not passing
Answer
Headlights and tailight are out it is not the fuse or the switch on a 2001 kawasaki zx6r
Answer
What year model is this vin no please ZX 600E004957 thank you
Answer
Main and big end bearing torque - 1997 kawasaki ZX-6R Ninja
Answer
Zx6r erratic throttle
Answer
Picture of the ignition wires and where they go on a 1986 zx600 kawasaki ninja (you did not show the option for a 1986 model zx600 model)
Answer
Hi, can you tel me what size hex socket i need to remove the front wheel on my kawasaki zx6r g1
Answer
1999 Kawasaki ZX-6R Ninja overheating
Answer
My battery is not holding a charge. it sometimes charges at high rpms but other then that it doesnt hold a charge so the bike doesnt start unless i use a charging pack each time
Answer
Its a 99 ninja not a 97. cant find where to edit question lol
Answer
1998 Kawasaki ZX-6R Ninja will not rev up past 6,000 rpm
Answer
Ive lost my key to my 1999 kawasaki zx6r how can i get another one
Answer
I noticed a crack on the lower side of the frame on the right of my gas tank. Is this something that could be fixed and how? Anyone know where a guy could find a new frame? 97 Kawasaki zx6r
Answer
Cant get the bottom bearing off the steering shaft
Answer
Cant get the riders seat off
Answer
Extremely hard to shift into 3rd gear, and if you do get it into 3rd gear its difficult to downshift back to 2nd gear. ive checked the shift forks but they dont seem to be bent or worn what else could cause this??
Answer
Why dont i have 5th gear on my 1996 Kawazx6r
Answer
1999 Kawasaki ZX-6R Ninja how to replace the pulse coil
Answer
How do I balance the carbs on my 1996 Kawa ZX6R
Answer
What could be the problem that there is no 5th gear on my 1996 Kawa ZX6R
Answer
My clutch is controlling the power of the batt. therefore the bike wont start,i replaced the entire switch assembly on the clutch lever, and still nothing... starter battery clutch lever is all good , as I read im leaning towards it being the actual power switch , but then why would the clutch control everything that's going on
Answer
At the same time I can push start the bike and everything works fine ,clutch clutch lever everything works fine when im riding , just when I stop the bike acts like its dead , at the same time when im trying to start the bike theres a popping in my cylinoid by the batt , at the same time I was stucn the side of the road , and I took a flathead to my clutch lever under where the switch is, beside the switch theres that black button thing that engauges when u squeeze the clutch lever , so I pushed that in and out and worked it back and forth and it worked for about 2 months , now im having the same problem , so I replaced the entire switch assembly and still does the same thing ???
Answer
I'm having a problem with m 2008 ZX6R that it won't go past 75-80mph & the rpms won't go higher than 8-9K. I was told that it's because my top injectors aren't spitting out, is this correct?
Answer
Ok, so we had heavy rain recently and I wasn't around to cover my bike. I put key in and all the gauges light up and do the normal operation even the headlights, tail, and side markers. But when I push the ignition I get a single click from the junction box. you can feel the click when you put your hand on box. Whilst doing this the gauges and instrument cluster dim. when you let go of the ignition button same click is heard and gauges return to normal and needles move as if barely inserting keys. Please help not a lot of cash on hand and rather do this myself
Answer

Helpful Links

Helpful Social

Copyright © 2024 QA.XPDF.PUB - All rights reserved.