Smartvac 4870 Bagged Upright Vacuum - User Guides | Support | Fine

Smartvac 4870 Bagged Upright Vacuum Owners Manuals, User Guides, Instructional Help Documents & Information.

Featured Questions

Preliminary list of posts to be most interested community
How to replace handle release eureka 4870? - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer
Brush roller not moving
Answer
Eureka Mod 4870. Replaced belt. Beater won't engage. Flat steel spring tensioner doesn't seem to be locked in place when selector in Carpet mode. Is there some sort of ''keeper'' that holds spring? Any diagram or picture available to show proper placement?
Answer
I got a cord wrapped around the roller, and now neither the roller nor the suction work...only hot air coming out the top of the base
Answer
Eureka The Boss Smartvac won't power. Where is the fuse?
Answer
Eureka Boss 4870gz shuts off (thermal protector) after 2 or 3 min
Answer
Belt tensioner overheated and doesn't keep belt tight enough
Answer
Brush roller spins until it touches the carpet, then stops. I have already replaced the belt and it continues to stop when it touches the carpet
Answer
4870 roller part number
Answer
Eureka 4870 thermostat
Answer
Replaced belt but isn't tight to turn roller - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer
Cannot change to floor position - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer

Latest Questions

Latest posts in community
Eureka Mod 4870. Replaced belt. Beater won't engage. Flat steel spring tensioner doesn't seem to be locked in place when selector in Carpet mode. Is there some sort of ''keeper'' that holds spring? Any diagram or picture available to show proper placement?
Answer
Brush roller not moving
Answer
Roller brush spins
Answer
Eureka Boss 4870gz shuts off (thermal protector) after 2 or 3 min
Answer
I got a cord wrapped around the roller, and now neither the roller nor the suction work...only hot air coming out the top of the base
Answer
My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?
Answer
Brush roller spins until it touches the carpet, then stops. I have already replaced the belt and it continues to stop when it touches the carpet
Answer
Eureka The Boss Smartvac won't power. Where is the fuse?
Answer
Eureka 4870 thermostat
Answer
4870 roller part number
Answer
Vacuum trips off as soon as started: new bag, free roller, clean filter
Answer
When I turn on my Eureka Smartvac 4870 is the light blinks sporadically and smells like the motor is burning. How can I tell if the motor needs to be replaced?
Answer
I have no suction - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer
Vacuum squeals when running. Big boss smart vac 4870
Answer
4870 Boss Smartvac. The vacuum tipped over and now the brush control lever will not stay in the carpet position. I can't get the brush to turn unless I push down and hold the lever. As soon as I let up on the lever the brush stops turning. Any ideas. The vacuum is only a month old
Answer
Replace the handle release pedal on an Eureka Boss Smartvac,
Answer
Dirt sensor red light doesn't come on - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer
Belt tensioner overheated and doesn't keep belt tight enough
Answer
My Eureka The boss Smartvac Model #4870 roller brush won't turn even on the highest setting and the belt smells hot. we took the belt off. How can you tell if it needs replaced?
Answer
Pedal release spring came out - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer
Cannot change to floor position - Eureka Smartvac 4870 Bagged Upright Vacuum
Answer
Foot lever for power
Answer
Eureka Boss Smart Vac won't lock in upright position
Answer
The hose split. I ordered a replacement but can't figure out how to remove or loosen the back panel to get the old hose out and the new one in
Answer

Helpful Links

Helpful Social

Copyright © 2024 QA.XPDF.PUB - All rights reserved.